Remember that recipe for the delicous cookies? Well here is an alternative to giving cookies to your friends, families and neighbors on a plate.
I love to recycle containers. There are so many uses for a Pringles container here is just one.
I love to recycle containers. There are so many uses for a Pringles container here is just one.
I had a lot of fun making these!
What you need:
-Pringles Can
-Printed paper
-Coordinating solid paper
-2 colors of ribbon (3/8" & 5/8")
-Embellishment (flower, bow, etc.)
-Printed or stamped tag
-Hole punch
-Scizzors & paper cutter
-Adhesive
Clean out your Pringles can. I used the spray dust remover to get the crumbs out and a wet paper towel with a little soap.
Measure your printed paper and solid paper by wrapping it around the can to see where you want to cut it. Mark it & cut it. Then glue it to the can. At the seem where the 2 papers meet glue ribbon (either 3/8" or 5/8").
Glue embellishment and tag close to the ribbon, making sure the paper seem down length of the can is in the back.
Using hole punch, punch 2 holes on top making sure they will be on the sides when the can is facing front. Using 5/8" ribbon insert one end in hole, wait to cut it, and tie a knot on the inside of the can. You may have to tie it twice to make it large enough so it doesn't come out. Now cut the ribbon leaving about 3 inches or slack. This will make it easier to tie the other side.
Now for the final touches. Glue 3/8" ribbon around the edge of the lid. Cut the printed paper in a circle cutter. I have a circle cutter than I use but if you don't you can use the lid as a template. Glue that to the top of the lid.
Tada! Now you have a cute canister for cookies or anyother treat.
What you need:
-Pringles Can
-Printed paper
-Coordinating solid paper
-2 colors of ribbon (3/8" & 5/8")
-Embellishment (flower, bow, etc.)
-Printed or stamped tag
-Hole punch
-Scizzors & paper cutter
-Adhesive
Clean out your Pringles can. I used the spray dust remover to get the crumbs out and a wet paper towel with a little soap.
Measure your printed paper and solid paper by wrapping it around the can to see where you want to cut it. Mark it & cut it. Then glue it to the can. At the seem where the 2 papers meet glue ribbon (either 3/8" or 5/8").
Glue embellishment and tag close to the ribbon, making sure the paper seem down length of the can is in the back.
Using hole punch, punch 2 holes on top making sure they will be on the sides when the can is facing front. Using 5/8" ribbon insert one end in hole, wait to cut it, and tie a knot on the inside of the can. You may have to tie it twice to make it large enough so it doesn't come out. Now cut the ribbon leaving about 3 inches or slack. This will make it easier to tie the other side.
Now for the final touches. Glue 3/8" ribbon around the edge of the lid. Cut the printed paper in a circle cutter. I have a circle cutter than I use but if you don't you can use the lid as a template. Glue that to the top of the lid.
Tada! Now you have a cute canister for cookies or anyother treat.
I gave this one to a friend for her birthday.
These other 2 I gave to the women I visit teach.
I really like the felt flower on this one. I used a template from Craft Gossip.
I really like the colors of this one. It is very bayberry creek Crafter colors :)
I am not in love with the bow I did and if I did it over I would make it smaller.
** Make sure when you make your cookies you make them the right size to fit in the canister**
~Rachel~
I am not in love with the bow I did and if I did it over I would make it smaller.
** Make sure when you make your cookies you make them the right size to fit in the canister**
~Rachel~